Back to the guides

Mounting your Harva Outdoors soft-shell tent

Illustration av bil med monterat mjukskalstält från Harva Outdoors på takräcket

Mounting your soft-shell tent (Viken or Udden) for the first time? Here we go through the whole process step by step – from unpacking and mounting rails to lifting the tent onto the roof.

Download the mounting instructions as a PDF (Swedish) – handy to print out and keep beside you in the garage.

Before you start

  • Tools: an Allen key and a 13 mm spanner come with the tent – you don't need any tools of your own
  • Space: plenty of floor space and four trestles – two for the folded tent, two more for when you unfold it
  • Help: one or two people to help when the tent is lifted onto the roof
  • Roof rack: must already be fitted and checked against the car's permitted roof load

If the roof rack isn't fitted yet, start with the guide to choosing the right roof rack and work out your car's roof load first. The tent counts as load on the roof even when it's closed.

What's in the box

Box contents: rooftop tent, mounting rails, Allen bolts, slide plates with M8 bolts, stainless steel plates with lock nuts, ladder with ladder brackets, cover, tools, pole, window rods and string light

Rooftop tent, mounting rails, Allen bolts, slide plates with M8 bolts, stainless steel plates with lock nuts, ladder with two ladder brackets, black cover, Allen key and 13 mm spanner, entrance pole, window rods (6 for Viken, 8 for Udden) and a string light with Velcro straps. Screws, slide plates, bolts, plates, lock nuts and tools are in the accessory bag. A cargo net and a storage bag for the window rods are also included.

Step 1 – Unpack and prepare

Folded rooftop tent on two trestles, with two more trestles in line, and the underside with the four pre-drilled holes

  1. Lay the folded tent on two trestles. Place two more in line – they'll take the tent when it's unfolded.
  2. Unfold the tent so it rests on all four trestles and open all the openings, including the side windows.
  3. Take out all the parts: mounting rails, accessory bag, ladder and the black cover.
  4. Lay the tent upside down and remove the black stickers marking the four pre-drilled holes.

Step 2 – Attach the mounting rails

The tent on two trestles with the upper base plate raised to 45 degrees, a sleeping bag between the plates and the rails being screwed on from inside

  1. Remove the end caps from the mounting rails and slide the small lock nuts (M6) into the rail channels.
  2. Leave the tent on two trestles, upside down. Raise the upper base plate to about 45 degrees and fold the mattress out of the way.
  3. Put a sleeping bag or a few pillows between the base plates so the tent can't fold shut while you work.
  4. Hold the rail in place against the upper base plate and screw it on with the Allen bolts, from inside the tent through the base.

Safety: Never work without something soft between the base plates – you could trap your fingers. Don't use the ladder as a stop; it slips out easily.
Tip: The rail nearest the hinge is hard to reach from the tent entrance. Open the side windows before you start.

Step 3 – Slide in the slide plates

Slide plate with the bolt head locked in the recess, and the plates being pushed towards the middle of the rail

  1. Slide the slide plates with bolts into the rails. The bolt head locks into the plate's recess – these are the bolts that fix the tent to the roof rack.
  2. Push the plates towards the middle of the tent before the lift, to reduce the risk of the bolts scratching the car.

Tip: If you have a low-profile roof rack, measure to check the bolts aren't too long.

Step 4 – Thread in the cover's zip

The tent from below: the zip is threaded in from the hinge side, up one side, around the corners and down the other

  1. Take out the pillows, lower the tent and separate the zip from the cover.
  2. Turn the zip so the seam faces inwards towards the tent fabric.
  3. Start at the hinge side, next to the bolt heads, and thread the zip into the track – up one side, around the corners and down the other.
  4. The cover itself goes on later, in step 6 point 4 – once the ladder is fitted.

Tip: The corners take a little patience – take your time and the zip will follow round nicely.

Step 5 – Fold the tent over onto trestles 3 and 4

The tent is folded over around the hinge from trestles 1–2 to trestles 3–4 so the mounting rails face down

  1. Check that trestles 3 and 4 are in line with trestles 1 and 2.
  2. Fold the upper base plate over around the hinge so it lands on trestles 3 and 4 – the mounting rails end up facing down.
  3. Under the base plate without mounting rails: clip on the storage bag for the window rods and hang the cargo net. It's easiest now, before the ladder is fitted.

Safety: Have two people when you fold the tent over, and don't let it drop onto the trestles.

Step 6 – Fit the ladder

The ladder in place under the tent with two ladder brackets, and a detail of the bracket with the spring-loaded pin that locks the ladder's tab

  1. Lay the tent with the mounting rails facing down and open the zip at the tent entrance.
  2. Bolt on the two ladder brackets through the pre-drilled holes with the four Allen bolts and matching lock nuts.
  3. Pull out the spring-loaded pin on the bracket, place the ladder with the warning labels facing up and insert the tabs into the slots. Release the pin – it slides in and locks the ladder.
  4. Pull the cover on from the side where the mattress is visible and close the zip without catching the tent fabric.

Note! Tighten the lock nuts firmly, but not so hard that the base plate is damaged.

Step 7 – Lift and secure the tent

The rooftop tent is lifted onto the roof rack by two to three people and secured with plates under the load bar, one bolt on each side

  1. Lift the tent onto the roof rack together with one or two helpers.
  2. Slide the slide plates so they sit on either side of the load bars.
  3. Check the position – see the list below.
  4. Secure the tent with the stainless steel plates and lock nuts under the load bars. Tighten with the 13 mm spanner.

Check the position:

  • The tent follows the car's lines so air can pass easily
  • The tailgate clears when open
  • The ladder ends up on the side where you want the entrance
  • The total height clears the garage door and barriers where you usually drive

Don't overtighten: Don't tighten too hard – what matters is that the lock nut can do its job. Overtightening is more likely to damage the roof rack than make the fixing more secure.
Tip: In rare cases, depending on the roof rack, the M8 bolts need to be replaced with bolts about 10 mm longer.

After mounting

  • Retighten all fixings after the first few hundred kilometres
  • Then retighten before every season and after long trips on rough roads
  • Open the tent once at home on the driveway before the first trip
  • Check that the cover is tight before you drive off

The string light

String light fastened with Velcro straps around the ridge pole, connected to a power bank via USB

The tent comes with a dimmable string light with three light modes.

  1. Hang the string light around the ridge pole using the Velcro straps provided.
  2. Connect it to a USB socket – a power bank works well.
  3. Choose a light mode and dim it to the level you want.

Frequently asked questions about mounting a rooftop tent

Can I mount the rooftop tent myself?

You can do most of it yourself, but we recommend doing the lift onto the roof together with one or two others – especially the first time.

What tools do I need?

An Allen key and a 13 mm spanner come with the tent, so you don't need any tools of your own. Just make sure you have plenty of floor space and four trestles to rest the tent on during mounting.

Do I have to take the rooftop tent off between trips?

No. Many people leave the tent on all season. Just remember that it counts as load on the roof even when closed, and that it affects height and fuel consumption.

Which way round should the tent go?

There's no right or wrong. Make sure the tailgate clears, the ladder ends up on the side you want the entrance and the tent follows the car's lines.

How tight should the bolts be?

Moderately tight. The lock nut needs to be able to do its job – overtightening is more likely to damage the roof rack than make the fixing more secure.

The bolts don't reach through – what do I do?

It happens in rare cases depending on how the roof rack is built. The M8 bolts then need to be replaced with ones about 10 mm longer.

Can you mount the tent for me?

Yes. We mount rooftop tents in Kumla if you'd rather drop off the car than do the job yourself.

We hope you'll have many great times in and around your rooftop tent. The next step is to open the tent – and then the packing list for your first night.

Run into problems with the mounting? Don't hesitate to get in touch via the contact page or on social media.

Back to the guides