Back to the guides

Opening your Harva Outdoors soft-shell tent

Illustration av uppfällt mjukskalstält med stege, byglar och teleskoprör

Have you mounted your soft-shell tent (Viken or Udden) and want to open it? Here we go through it step by step – from packed to ready for bed. If you haven't mounted the tent yet, start with the mounting guide for soft-shell tents.

Download the opening guide as a PDF (Swedish)

Step 1 – Open the cover

Packed rooftop tent with cover: transport straps, Velcro flap and zip marked

  1. Undo the transport straps over the cover.
  2. Open the Velcro flap at the bottom of the cover – it covers the zip.
  3. Unzip the cover all the way around the tent.
  4. Fold back the cover and let it hang down along the side of the car.

Step 2 – Unfold the tent

The tent is unfolded over the hinge using the ladder as a lever, and the ladder is set on the ground

  1. Undo the Velcro straps holding the folded tent together.
  2. Take hold of the ladder and unfold the tent – the ladder works as a lever.
  3. Adjust the ladder length so it stands firmly on the ground and supports the unfolded section. All rungs not in use should be pushed up against the base plate.

Note! The ladder won't lock unless the unused rungs are pushed up against the base plate.

Step 3 – Deal with the cover

The cover rolled up at the hinge under the open tent, secured with the transport straps

  1. Roll the cover up towards the hinge and secure it with the transport straps – clamp the straps between the base plates at the hinge.
  2. If you'd rather remove it, slide it out of the keder rail, fold it up and put it under the car.

Step 4 – Fit the pole over the entrance (Viken)

The pole over the entrance runs from the corner of the tent fabric to the sleeve at the base plate

  1. Take out the pole and fit it into the corners of the tent fabric.
  2. Push the pole onto the sleeves on each side of the entrance.

Step 5 – Seal the gap at the hinge

The fabric panel is folded down over the split in the tent fabric at the hinge and secured with Velcro

  1. The tent fabric is split at the hinge – that split is what lets the tent fold.
  2. The fabric panel is sewn in at the top. Fold it down over the gap and press the Velcro into place so it seals.

Step 6 – Fit the telescopic pole (Viken)

The telescopic pole with forks at both ends between the pole over the entrance and the outermost pole

  1. Press the telescopic pole's fork onto the pole over the entrance.
  2. Press the other fork onto the tent's outermost pole.

Step 7 – Fit the window rods

The window rods run from the folds in the base plate up through the eyelets in the rain awning over the window

  1. Take the window rods out of the storage bag under the base plate. Insert the rod into the base plate, where the small fold in the tent fabric is.
  2. Stretch out the rain awning and push the end of the rod through the awning's eyelet.
  3. Do the same at every window – 6 rods on Viken, 8 on Udden.

Alternative: If you want the window fully open, you can roll up the window fabric instead and secure it with the straps above the window.

In rough weather – guy lines and tent pegs (Viken)

Guy lines from the bottom edge of the tent fabric at the entrance, pegged into the ground

  1. Guy lines and tent pegs come with the tent.
  2. Attach the guy lines to the bottom edge of the tent fabric at the entrance.
  3. Tension the lines and peg them into the ground.

Tip: On hard ground where the pegs won't go in, use a heavy weight instead, such as a 5 kg barbell plate.

Before you climb in

  • The ladder stands firmly and is set correctly
  • The gap at the hinge is sealed
  • The window rods are in place – on Viken, the entrance pole and telescopic pole too
  • The guy lines are tensioned if it's windy

Good to know: Under the unfolded section there's a cargo net – perfect for shoes, clothes and anything else you want close at hand. That's also where the storage bag for the window rods is.

Next up is the packing list for your first night. Any questions about opening the tent? Get in touch via the contact page.

Back to the guides